All Categories
US$

Cart

Loadding...

Reviews (13)

Write a Review
Rating
  • Ro****er
    Great for what I'm doing
    2026-08-06
  • Se****ar
    For my personal use (home, backyard & garage...), I'm more than satisfied with this purchase. It's better than good enough for my purposes. Way heavier built than I was expecting. Weighs 190 grams. Externally almost everything is metal & glass. There is one tiny higher quality hard plastic spacer on the back of the beam ruler, near the depth measurement; it's purpose is just to allow the caliper to set flat, so I'm not concerned about that. As noted by another reviewer, I also observed the metric conversion to be slightly off. The camera angle didn't capture this well, but I did the following test: Open caliper until it reads straight up 1.00 , at which point it should also read 25.4mm. Instead it read just below the 25.42mm mark (probably about 25.416mm, based on me inferring the needle placement). More than good enough at this price range. As the other reviewer also noted, for more accurate metric readings, do the math conversion yourself after taking an SAE measurement. Or use a micrometer if it needs to be that precise.
    2025-06-29
  • Fr****yo
    I actually own an iGaging 6 caliper (decimal and fractions) and I have nothing but good to say about that caliper, it is smooth and very nice. I was about to purchase this caliper except that if you do the math you will see that either the metric or the SAE measurement will be wrong. The problem is that 0.1 inches does not equal 2.0 mm. 0.1 inches is 2.54 mm. The engineer who came up with the dial for this caliper needs to be reprimanded, it is simply wrong. I'm a licensed mechanical engineer, things like this tend to jump out at me.
    2023-10-25
  • Ed****on
    When checking with my other gauges, this seems accurate. Also I like the dual readings.
    2022-06-23
  • La****se
    Been using for over a month. Readings are accurate. Good buy
    2022-02-15
  • Br****ce
    IGaging makes well made measuring equipment at reasonable prices. I am comfortable that the measurements are going to be good enough for my uses, which are not professional. The measurements of my 1-2-3 blocks were spot on.
    2020-08-26
  • No****er
    I have to revise this down (original review was 5 star), this is because of durability. I know this is a precision tool, but stuff happens, and I have had other calipers survive a fall from my desk. These did not. After falling 24inches, the internal gears were jammed and the unit was rendered unusable. This suggests to me that the gears are plastic, nylon or similar. I'm not going to beat them up with a 'bad' review, because the product is still pretty good at what it does. And I should have been more careful... However I have similar tools from other manufacturers that have survived a similar fall with no problem. That too me suggests a durability issue This is a great caliper. Dual reading is the main reason I got it, but accuracy down to 1000'ths was a surprise. My old calipers were only down to 100ths at the same price. I checked this claim against known good 123 block, and against a known accurate micrometer and it was off by about 2/10000ths (yes, ten-thousands.. tiny). Way more accurate than anything I'm doing, I'm not building a spaceship.
    2020-05-11
  • Pi****az
    This is one of many growing number of measurement tools I have from iGaging. I also have Starrett, Mitutoyo and other high end digital tools, but when I need something that just works, feels good in my hand, and is reliable, I grab the iGaging. It seems like all too often when i grab a Digital caliper or level, or whatever, it needs a battery or recalibration, or something. This just works and the dial gives a quickly recognizable measurement. no more scratching my head if 17/64 is bigger or smaller than 1/4. This is metric, so that doesn't come into play as much, but you know what I mean. I can easily see if 2.02 cm is a big gap or close enough. Great tools. Unbelievable price. Just as accurate as the expensive stuff. Thanks iGaging.
    2018-06-09
  • Du****ra
    I understand that this is the absolute nittiest nit pick ever, since this is not a micrometer, but I have 0.002in shim stock here, and while the SAE readout is BANG ON (extremely impressive) the metric readout is wrong. There is drift. At each end, it slowly drifts away from what the SAE is reading out by about 20 microns total over the length of the unit. Again, this is a crazy thing to care about at this price, but I do want to inform. If you need to read at the extremes, read in SAE and convert to metric yourself.
    2018-06-05