All Categories
US$

Cart

Loadding...

Does the Weld Fit the Drawing?

Nov 17, 2026
WELDINGSTOPFIELD NOTES / 02
The gauge series · Fillet welds

Does the weld
fit the drawing?

Four small templates make two useful checks visible: weld leg length and the outside throat profile.

4-PIECE FILLET WELD GAUGE SET / INCH + METRIC
WeldingStop four-piece stainless steel fillet weld gauge set on chain

The bead can look full and still need a closer check.

A raised weld face is easy to notice. Leg length is less obvious. Start with the drawing’s required size, then choose the matching edge on the gauge. The set also has profiles for comparing the outside shape of the weld throat.

Know the four pieces

Pick the edge before you measure.

The engraved inch and rounded metric values correspond across each piece.
Gauge A from the WeldingStop four-piece fillet weld gauge setA / LEG LENGTH

Check both legs separately.

Gauge B from the WeldingStop four-piece fillet weld gauge setB / THROAT PROFILE

Smaller sizes, 1/8–5/16″.

Gauge C from the WeldingStop four-piece fillet weld gauge setC / THEORETICAL THROAT

External profile reference.

Gauge D from the WeldingStop four-piece fillet weld gauge setD / THROAT PROFILE

Larger sizes, 3/8–3/4″.

Choose a check

Two checks, one joint.

Tap a card for the matching setup and method from the WeldingStop manual.
Manufacturer instruction illustration showing a fillet weld leg length gauge against a T-joint
Measurement 01

Leg length

  1. Let the weld cool and remove slag, spatter, and dirt.
  2. Choose gauge A and the size required by the drawing.
  3. Set the reference edge flat on the adjacent plate and hold the checking edge square to the joint.
  4. Compare the weld toe with the selected edge. Do not tilt or force the gauge.
  5. Check the other leg separately, then repeat at several places along the weld.

A convex face does not by itself prove that both legs are long enough.

Manufacturer instruction illustration showing a throat profile gauge seated across a fillet weld
Measurement 02

Throat profile

  1. Choose the size and the matching throat-checking profile: B for smaller sizes, D for larger sizes, or C for the theoretical-throat reference.
  2. Seat the gauge reference surfaces against both adjoining plates.
  3. Compare the weld face with the checking tip or profile, without rocking the gauge.
  4. Repeat at several points to see whether the profile changes along the weld.

This is an external profile comparison. It cannot verify internal penetration or fusion.

Where it earns its place

Look beyond the bead's shine.

Use the project drawing and inspection requirements to decide acceptance.
01 / BRACKET FABRICATION
Cooled fillet weld on a steel T-joint

At a T-joint

Compare both weld legs after cleaning. The visible bead shape may hide an uneven leg.

02 / REPEATED PARTS
Three fabricated steel T-joints in a row

Across a batch

Use the same required size to check several welds and catch variations between parts.

03 / FINAL VISUAL CHECK
Inspector recording a visual check beside a welded T-joint

Before sign-off

Record the observed leg and profile checks beside the drawing requirement.

Choose the profile.
Seat it. Compare.

The four stainless-steel gauges cover marked sizes from 1/8″ to 3/4″, with corresponding metric markings. A gauge supplies a comparison; the drawing or inspection plan supplies the limit. The theoretical-throat template does not reveal what is happening inside the weld.

Product, sizes, and method reference: WeldingStop 4-Piece Fillet Weld Gauge Set user manual, pp. 1–3. Product and setup images: WeldingStop. Scene photos are AI-generated illustrations. Instruction images are reference examples; inspect the actual weld and gauge in use.

<< Fillet Weld Gauge vs Bridge CAM Gauge — Which to Buy

>> Before the Weld, Check the Fit