Fillet Weld Gauge vs Bridge CAM Gauge — Which to Buy
TL;DR
Buy a fillet weld gauge set if you mostly check fillet leg and throat on finished T-joints. Buy a Bridge CAM (MG-8) when one tool has to cover fillet size plus reinforcement, undercut/pit, misalignment, and bevel angle. WeldingStop sells both under welding gauges. They’re dimensional aids—not a substitute for code acceptance calls or NDT.
Shop: WELDING GAUGE · Bridge CAM Gauge
Related: Which welding gauge should you use?
Applicable / Not applicable
| Applicable | Not applicable |
|---|---|
| Fab QC, shop-floor checks, training kits for accessible surface weld geometry | Replacing procedure qualification, visual-acceptance judgment, or UT/RT |
| Choosing between a 7-piece fillet set and an MG-8 Bridge CAM for fillet-heavy work | Assuming one Bridge CAM replaces a Hi-Lo pipe internal gauge |
| Inch, metric, or dual-scale buyers who know which scale their drawings use | Claiming AWS/ASME “certified gauge” status (not asserted here) |
| Complementary reading with the site’s gauge selection guide | Using a fillet blade to measure pipe high-low |
Quick decision
| Your primary job | Buy this | Why |
|---|---|---|
| Mostly fillets—leg / throat / concave-convex | 7-piece fillet gauge set (e.g. MG-11 / WSG-01009 family) | Fast go/no-go blades sized for fillet features |
| Fillet plus reinforcement, undercut, outside misalignment, bevel | Bridge CAM MG-8-A or MG-8-B | One cam tool, several measuring modes |
| Need fillet speed and multi-feature audits | Fillet set and Bridge CAM | Common inspector kit pairing |
| Pipe internal high-low | Neither alone—grab a Hi-Lo from the welding gauge category | Different measurement |
Bought a fillet-only set for a pipe fab bay once? You’ll be back for Hi-Lo the first time someone asks for internal mismatch. Fillet blades don’t do that job.
Side-by-side comparison
| Feature | Fillet gauge set (7-piece) | Bridge CAM (MG-8) |
|---|---|---|
| Main purpose | Fillet leg & throat / profile checks | Multi-feature weld & prep checks |
| Typical WS models | 7-piece sets (WSG-01009 and related MG-11 listings); also adjustable MG-3 | MG-8-A (WSG-01006), MG-8-B (WSG-01007), metric MG-8 variants |
| Fillet leg | Yes (blade / set dependent) | Yes (model range dependent) |
| Fillet throat | Yes (set dependent) | Yes (e.g. MG-8-A lists throat range) |
| Seam reinforcement | Limited / not the focus | Yes |
| Undercut / pit depth | Limited / not the focus | Yes |
| Outside misalignment | Usually no | Yes |
| Bevel angle | Usually no | Yes (e.g. 0–60°) |
| Best for | Dedicated fillet QC, welders checking own work | Inspectors bouncing between several dimensions |
| Learning curve | Low—pick the marked blade | Moderate—pick the right cam mode and scale |
What a fillet gauge set is for
A 7-piece fillet weld gauge is a pocket set of stainless blades marked for common fillet sizes. Seat the right profile on the weld to check leg length and, on many sets, throat or concave/convex.
Choose fillet-first if:
- Most drawings call out fillet size only.
- Welders need a cheap, fast check at the booth.
- You already own other tools for undercut or bevel.
WeldingStop starters:
- 7 Pieces Fillet Leg/Throat Gauge (Inch/mm) — WSG-01009
- Related 7-piece metric-reading listings and larger fillet sets in WELDING GAUGE
- Adjustable option: MG-3 adjustable fillet gauge (same category)
Limit: Leg and throat are different acceptance features. An external profile check does not prove fusion or internal soundness. Don’t treat a green blade as a green weld.
What a Bridge CAM (MG-8) is for
A Bridge CAM gauge uses an adjustable cam/bridge so one tool can read several accessible dimensions. On WeldingStop’s MG-8-A listing, example ranges:
| Measurement (MG-8-A example) | Example range on product page |
|---|---|
| Outside misalignment | 0–25 mm / 0–1 in |
| Undercut / pit depth | 0–25 mm / 0–1 in |
| Seam reinforcement | 0–25 mm / 0–1 in |
| Fillet throat | 0–20 mm / 0–3/4 in |
| Fillet leg length | 0–25 mm / 0–1 in |
| Bevel angle | 0–60° |
Exact scales vary by SKU (MG-8-A vs MG-8-B vs metric-only MG-8). Read the product table before ordering.
Choose Bridge CAM if:
- One inspector covers prep + final visual dimensions.
- You measure reinforcement and undercut as often as fillets.
- You want dual inch/metric on one tool (many MG-8 listings).
WeldingStop starters:
- MG-8-A Bridge CAM — WSG-01006
- MG-8-B Bridge CAM — WSG-01007
- Category: Bridge CAM Gauge
Limit: Bridge CAM does not replace a Hi-Lo for internal pipe mismatch, and it does not replace required volumetric NDT. Wrong mode on the cam = confident wrong number. Slow down and match the feature you’re measuring.
Which to buy — practical scenarios
| Scenario | Recommendation |
|---|---|
| Structural fab shop welding mostly fillets | Start with a 7-piece fillet set; add Bridge CAM when QC expands |
| Job-shop QA with mixed groove + fillet work | MG-8 Bridge CAM first |
| Mobile repair / farm fab kit | Fillet set for speed; Bridge CAM if space allows only one multi-tool |
| Training class | Fillet set for students + one Bridge CAM for demos |
| Pipe fabrication fit-up | Add Hi-Lo (and taper/gap tools) from WELDING GAUGE—don’t stretch fillet/CAM tools past what they can reach |
How this complements the existing gauge guide
The site guide Which welding gauge should you use? maps seven tool types (caliper, feeler, taper, fillet, V-WAC, Hi-Lo, Bridge CAM). This page answers the narrower buy question: fillet set vs Bridge CAM—then points you at the right category SKUs.
Buying checklist
- List the features you measure weekly (fillet only vs multi-feature).
- Confirm inch, metric, or dual against drawings.
- Check range on the product page (throat/leg maxima differ by model).
- Prefer stainless tools with clear laser markings and a case for field kits.
- Record readings against the drawing / WPS / customer criteria—gauges measure; they don’t accept the weld for you.
FAQ
Do I need a Bridge CAM if I only weld fillets?
Not required. A 7-piece fillet set is usually enough. Buy MG-8 when you also check reinforcement, undercut, misalignment, or bevel.
Is MG-8-A or MG-8-B better?
Compare the measurement list and scales on each product page. MG-8-A listings emphasize multi-feature ranges; MG-8-B is positioned strongly for fillet throat—verify current specs before choosing.
Can these gauges certify my weld to code?
No. They support dimensional checks. Acceptance follows your contract documents and qualified inspection judgment.
Where do V-WAC and Hi-Lo fit?
V-WAC focuses on undercut/reinforcement-style checks; Hi-Lo on pipe internal misalignment. See the welding gauge category and the seven-tool guide linked above.
CTA
- Fillet-focused: WELDING GAUGE category → 7-piece fillet set WSG-01009
- Multi-feature QC: Bridge CAM Gauge category → MG-8-A · MG-8-B
- Read next: Which welding gauge should you use?
- Company Info
- ABOUT US
- Contact Us
- Returning & Refund
- Terms & Conditions
- Privacy Policy
- Insurance
- Feedback
- W.S.Sitemap
- User Center
- Forgot Password
- My Orders
- Tracking Order
- My Account
- Register
- Payment & Shipping
- Estimated Delivery Time
- Locations We Ship To
- Payment Methods
- Shipping Insurance
- FAQ
